WeTek Community Forum
Hi WeTek Fan! :)

Please check our WeTek Closed BETA program: http://www.wetekforums.com/v/discussion/31382/call-for-closed-beta-on-wetek-play-2?new=1

Thanks
MasterChief117

Help needed: Wetek Play DVB-S/S2 VDR Unicable

RicoNRWRicoNRW Posts: 1WeTek Community Member
Hi,

I have my Wetek Play DVB-S/S2 running without problems on Android Theatre. i just had to configure unicable frequencies and SCR (in my case SCR=2 Frequecie =1400mhz) and all Channels run perfectly.
But i can´t make it run with OpenElec6.0 and Kodi.
As shown in other threads and tutorials i installed VDR backend and frontend.
made the src.conf, diseqc.conf and setup.conf canges in /storage/.kodi/userdata/addon_data/service.multimedia.vdr-addon/conf/
Same changes in /storage/.kodi/addons/service.multimedia.vdr-addon/conf
Also copied a channels.conf there.
When booting the box "Live TV" appears and i can see the channellist but when trying to run a channel it shows "VNSI client - Channel: No Data" on all channels.
I spend a couple nights to figure out what to do but can`t bring it to work so maybe someone can find my problem.

These are my config-files:
diseqc.conf:

# DiSEqC configuration for VDR
#
# Format:
#
# satellite slof polarization lof command...
#
# satellite: one of the 'S' codes defined in sources.conf
# the special value 'S360E' means that this entry uses a positioner
# (command 'P') that can move the dish to any requested satellite
# position within its range
# slof: switch frequency of LNB; the first entry with
# an slof greater than the actual transponder
# frequency will be used
# polarization: V = vertical, H = horizontal, L = Left circular, R = Right circular
# lof: the local oscillator frequency to subtract from
# the actual transponder frequency
# command:
# t tone off
# T tone on
# v voltage low (13V)
# V voltage high (18V)
# A mini A
# B mini B
# Pn use positioner to move dish to satellite position n (or to the
# satellite's orbital position, if no position number is given)
# Sn satellite channel routing code sequence for bank n follows
# Wnn wait nn milliseconds (nn may be any positive integer number)
# [xx ...] hex code sequence (max. 6)
#
# The 'command...' part is optional.
#
# A line containing space separated integer numbers, terminated with a ':',
# defines that any following DiSEqC sequences apply only to the given list
# of device numbers.
#
# Examples:

# Full DiSEqC sequence:

S19.2E 11700 V 9750 t v W15 [E0 10 38 F0] W15 A W15 t
S19.2E 99999 V 10600 t v W15 [E0 10 38 F1] W15 A W15 T
S19.2E 11700 H 9750 t V W15 [E0 10 38 F2] W15 A W15 t
S19.2E 99999 H 10600 t V W15 [E0 10 38 F3] W15 A W15 T

S13.0E 11700 V 9750 t v W15 [E0 10 38 F4] W15 B W15 t
S13.0E 99999 V 10600 t v W15 [E0 10 38 F5] W15 B W15 T
S13.0E 11700 H 9750 t V W15 [E0 10 38 F6] W15 B W15 t
S13.0E 99999 H 10600 t V W15 [E0 10 38 F7] W15 B W15 T

# Optimized for mini DiSEqC (aka toneburst):
#
# S19.2E 11700 V 9750 t v W15 A W15 t
# S19.2E 99999 V 10600 t v W15 A W15 T
# S19.2E 11700 H 9750 t V W15 A W15 t
# S19.2E 99999 H 10600 t V W15 A W15 T
#
# S13.0E 11700 V 9750 t v W15 B W15 t
# S13.0E 99999 V 10600 t v W15 B W15 T
# S13.0E 11700 H 9750 t V W15 B W15 t
# S13.0E 99999 H 10600 t V W15 B W15 T
#
# Optimized for full DiSEqC:
#
# S19.2E 11700 V 9750 [E0 10 38 F0]
# S19.2E 99999 V 10600 [E0 10 38 F1]
# S19.2E 11700 H 9750 [E0 10 38 F2]
# S19.2E 99999 H 10600 [E0 10 38 F3]
#
# S13.0E 11700 V 9750 [E0 10 38 F4]
# S13.0E 99999 V 10600 [E0 10 38 F5]
# S13.0E 11700 H 9750 [E0 10 38 F6]
# S13.0E 99999 H 10600 [E0 10 38 F7]
#
# DisiCon-4 Single Cable Network:
#
# horizontal: 11.704 - 12.205 GHz (1. IF: 1144 - 1645 MHz) - LOF 1 (10,56 GHz)
# horizontal: 12.676 - 12.709 GHz (1. IF: 2116 - 2148 MHz) - LOF 1 (10,56 GHz)
# vertical: 12.035 - 12.107 GHz (1. IF: 955 - 1027 MHz) - LOF 3 (11,08 GHz)
# vertical: 12.464 - 12.716 GHz (1. IF: 1744 - 1996 MHz) - LOF 2 (10,72 GHz)
#
# S19.2E 99999 H 10560 t v
# S19.2E 12110 V 11080 t v
# S19.2E 99999 V 10720 t v
#
# SCR (Satellite Channel Routing) EN50494:
#
# S19.2E 11700 V 9750 t V W10 S0 [E0 10 5A 00 00] W10 v
# S19.2E 99999 V 10600 t V W10 S1 [E0 10 5A 00 00] W10 v
# S19.2E 11700 H 9750 t V W10 S2 [E0 10 5A 00 00] W10 v
# S19.2E 99999 H 10600 t V W10 S3 [E0 10 5A 00 00] W10 v
#
# S13.0E 11700 V 9750 t V W10 S4 [E0 10 5A 00 00] W10 v
# S13.0E 99999 V 10600 t V W10 S5 [E0 10 5A 00 00] W10 v
# S13.0E 11700 H 9750 t V W10 S6 [E0 10 5A 00 00] W10 v
# S13.0E 99999 H 10600 t V W10 S7 [E0 10 5A 00 00] W10 v
#
# SCR (Satellite Channel Routing) EN50607 "JESS":
#
# S19.2E 11700 V 9750 t V W10 S0 [70 00 00 00] W10 v
# S19.2E 99999 V 10600 t V W10 S1 [70 00 00 00] W10 v
# S19.2E 11700 H 9750 t V W10 S2 [70 00 00 00] W10 v
# S19.2E 99999 H 10600 t V W10 S3 [70 00 00 00] W10 v
#
# S13.0E 11700 V 9750 t V W10 S4 [70 00 00 00] W10 v
# S13.0E 99999 V 10600 t V W10 S5 [70 00 00 00] W10 v
# S13.0E 11700 H 9750 t V W10 S6 [70 00 00 00] W10 v
# S13.0E 99999 H 10600 t V W10 S7 [70 00 00 00] W10 v
#
# S23.0E 11700 V 9750 t V W10 S8 [70 00 00 00] W10 v
# S23.0E 99999 V 10600 t V W10 S9 [70 00 00 00] W10 v
# S23.0E 11700 H 9750 t V W10 S10 [70 00 00 00] W10 v
# S23.0E 99999 H 10600 t V W10 S11 [70 00 00 00] W10 v
#
# S28.2E 11700 V 9750 t V W10 S12 [70 00 00 00] W10 v
# S28.2E 99999 V 10600 t V W10 S13 [70 00 00 00] W10 v
# S28.2E 11700 H 9750 t V W10 S14 [70 00 00 00] W10 v
# S28.2E 99999 H 10600 t V W10 S15 [70 00 00 00] W10 v
#
# Positioner for steerable dish:
#
# S360E 11700 V 9750 t V W20 P W20 t v
# S360E 99999 V 10600 t V W20 P W20 T v
# S360E 11700 H 9750 t V W20 P W20 t V
# S360E 99999 H 10600 t V W20 P W20 T V

S19.2E 11700 V 9750 t v S0 W10 [E0 10 5A 00 00] W10 v
S19.2E 99999 V 10600 t v S1 W10 [E0 10 5A 00 00] W10 v
S19.2E 11700 H 9750 t v S2 W10 [E0 10 5A 00 00] W10 v
S19.2E 99999 H 10600 t v S3 W10 [E0 10 5A 00 00] W10 v


src.conf:

# SCR (Satellite Channel Routing) configuration for VDR
#
# Format:
#
# channel frequency [pin]
#
# channel: SCR channel index (0-7)
# frequency: frequency of the SCR channel ("user band")
# pin: optional pin of the SCR channel (0-255)
#
# A line containing space separated integer numbers, terminated with a ':',
# defines that any following lines apply only to the given list
# of device numbers.
#
# Examples:

# EN50494 & EN50607 ("JESS")
# 0 974
# 1 1076
# 2 1178
# 3 1280
# 4 1382
# 5 1484
# 6 1586
# 7 1688
# EN50607 ("JESS") only
# 8 1790
# 9 1892
# 10 1994
# 11 2096
2 1400


setup.conf:

AdaptiveSkipAlternate = 0
AdaptiveSkipInitial = 120
AdaptiveSkipPrevNext = 0
AdaptiveSkipTimeout = 3
AntiAlias = 1
AudioLanguages =
ChannelEntryTimeout = 1000
ChannelInfoPos = 0
ChannelInfoTime = 5
ChannelsWrap = 0
ColorKey0 = 0
ColorKey1 = 1
ColorKey2 = 2
ColorKey3 = 3
CurrentChannel = 1
CurrentDolby = 0
CurrentVolume = 255
DefaultLifetime = 99
DefaultPriority = 50
DelTimeshiftRec = 0
DeviceBondings = 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
DiSEqC = 1
DisplaySubtitles = 0
EmergencyExit = 1
EPGBugfixLevel = 3
EPGLanguages =
EPGLinger = 0
EPGScanTimeout = 5
FoldersInTimerMenu = 1
InitialChannel =
InitialVolume = -1
InstantRecordTime = 180
LnbFrequHi = 10600
LnbFrequLo = 9750
LnbSLOF = 11700
MarginStart = 2
MarginStop = 10
MarkInstantRecord = 1
MaxVideoFileSize = 2000
MenuKeyCloses = 0
MenuScrollPage = 1
MenuScrollWrap = 0
MinEventTimeout = 30
MinUserInactivity = 300
MultiSpeedMode = 0
NameInstantRecord = TITLE EPISODE
NextWakeupTime = 0
NumberKeysForChars = 1
PauseAtLastMark = 0
PauseKeyHandling = 2
PauseLifetime = 1
PauseOnMarkJump = 1
PauseOnMarkSet = 0
PausePriority = 10
PositionerLastLon = 0
PositionerSpeed = 15
PositionerSwing = 650
PrimaryDVB = 1
ProgressDisplayTime = 0
RcRepeatDelay = 300
RcRepeatDelta = 100
RecordingDirs = 1
ResumeID = 0
ShowChannelNamesWithSource = 0
ShowInfoOnChSwitch = 1
ShowRemainingTime = 0
ShowReplayMode = 0
SiteLat = 0
SiteLon = 0
SkipEdited = 0
SkipSeconds = 60
SkipSecondsRepeat = 60
SplitEditedFiles = 0
StandardCompliance = 0
SubtitleBgTransparency = 0
SubtitleFgTransparency = 0
SubtitleLanguages =
SubtitleOffset = 0
SVDRPTimeout = 300
TimeoutRequChInfo = 1
TimeSource =
TimeTransponder = 0
UpdateChannels = 5
UseDolbyDigital = 1
UsePositioner = 0
UseSmallFont = 1
UseSubtitle = 1
UseVps = 0
VideoDisplayFormat = 1
VideoFormat = 0
VolumeLinearize = 0
VolumeSteps = 51
VpsMargin = 120
ZapTimeout = 3
wirbelscan.ATSC_type = 0
wirbelscan.CountryIndex = 82
wirbelscan.DVB_Type = 2
wirbelscan.DVBC_Inversion = 0
wirbelscan.DVBC_QAM = 0
wirbelscan.DVBC_Symbolrate = 0
wirbelscan.DVBT_Inversion = 0
wirbelscan.enable_s2 = 1
wirbelscan.logFile = 1
wirbelscan.SatIndex = 67
wirbelscan.scanflags = 31
wirbelscan.user0 = 0
wirbelscan.user1 = 0
wirbelscan.user2 = 0
wirbelscan.verbosity = 3
AlwaysSortFoldersFirst = 1
SetSystemTime = 0
epgsearch.SVDRPPort = 6419
OSDSkin = sttng


Comments

  • teafortwoteafortwo Posts: 3WeTek Community Member
    Hi Rico,
    the following seemed to work for me:
    1. Take care to get a clean openelec 6.0 installation
    2. Follow the steps that are described in the video tutorial for scanning dvb-s2
    But:
    in the menu configuration/dvb inputs/tv adaptors Folder Avalink --> select Unicable LNB, you should disable "Over the air epg"
    than below that you will find the hardware adaptor as an icon, there select the correct SCR ID and type in the correct frequency corresponding to the scr ID, normally:
    SCR ID 0 : 1210 MHz
    SCR ID 1: 1420 MHz
    SCR ID 2: 1680 MHz
    SCR ID 3: 2040 MHz
    you should disable "Tune before Diseqc", "Full DiseqC" and set DiseqC repeats to 0.
    That has worked tonight for me.
    In my configuration I have a twin tuner in my tv set, connected to SCR ID 0 and SCR ID 1, the Wetek play is connected to SCR ID 2 and 1680 MHz. I own an inverto unicable LNB.
    Hope this is helping you and others ;-)
    teafortwo

    Then proceed according to the tutorial video mentioned above (scanning, defining the mux and mapping - you should disable DISeQC
  • jayjay Posts: 29WeTek Community Member
    hi,
    at first you should give all 4 or 8 scr freqs in src.conf...
    jay
  • teafortwoteafortwo Posts: 3WeTek Community Member
    Oh ... And with the current Version of openelec/tvheadend I didn't edit scr.conf and didn't eben find the file. Using ssh I logged into the Wetek and performed a shutdown -r now every now and than. That did the Job here. I could configure tvheadend for unicable with the Web frontend completely.
    Regards
    Teafortwo
  • jayjay Posts: 29WeTek Community Member
    yes. these files are vdr things...
  • wenneswennes Posts: 2WeTek Community Member
    This helped me really with my JESS Installation.and VDR
    Thanks

    wennes
Sign In or Register to comment.
© Copyright 2014 - Creative Dreams | Powered by Vanilla
All times are UTC